2020 Rhino Equipment Wheel Loaders RWL102

Information

2020 Rhino Equipment Wheel Loaders RWL102

Rhino® Wheel Loaders are today’s solution to meet high performance requirments, have maximum uptime, and low cost operation. Designed to keep you competitive, these loaders let you finish the job faster and put more profit in your pocket.

The RWL series allows you to work hard and efficiently in all conditions. Repeatable fine modulation gives superior bucket control with less spillage. RWL Series electro-hydraulic implement controls and load-sensing hydraulic system with simultaneous lift and tilt capabilities offer better control with less effort.

Rhino® wheel loaders saves you money by keeping operating costs to a minimum – getting more work done per unit of fuel used.

Features may include:

  • If you`ve got maximum productivity in mind, the RWL Series Loaders should be at the top of your list. But it`s not just their big torque reserves thet make them such impressive performers. Joystick control provide smooth, near-effortless control. Rhino® hydraulics sense the load and deliver the flow needed for smooth combined functions and fast work cycles.
  • Control panel provides access to critical machine info, brake and throttle pedals are conveniently positioned for maximum comfort to the operator.
  • Rhino® cylinders offer superior strength and dent resistance deliver longer component life and reduced risk of system contamination. Rhino® Cylinders and Rods are designed to allow for a variety of service / repair options.
  • High quality hose products mean fewer hose changes. Rhino® Equipment offers a broad line of high, medium and low-pressure hoses and couplings that are engineered and tested far beyond industry standards for top performance and long life.

Photos

Highlights

  • Albany, Georgia
  • 2020
  • Rhino Equipment
  • Wheel Loaders RWL102
  • Model: 6BT5
  • Type: Powershift | Torque Converter: Single-stage, Dual-phase, Quad-element torque | Operator Interface: Steering column lever for two gears forward and one in reverse | Shift Modes: Manual activation (Forward: 1st and 2nd; Reverse: 1st)
  • Available
  • Bucket: 2,460 mm (8.1 ft)
  • Top of Cab and Canopy: 3,120 mm (10.2 ft) | Hood: 3,010 mm (9.9 ft) | Hinge Pin, Fully Raised: 3,732 mm (12.2 ft) | Dump Clearance, 45 degree Full Height: 2,850 mm (9.4 ft) | Reach, 45 degree Dump, Full Height: 1,030 mm (3.4 ft)

Specifications

  • 2020
  • Rhino Equipment
  • Wheel Loaders
  • RWL102
  • Large
  • Model: 6BT5
  • Cummins | Rhino®
  • Tier2
  • 6
  • 5.9 L (360 cu. In)
  • Net Power kW (Hp) @ Rated rpm: 87(117)@2,200 rpm
  • Net Peak Torque Nm (lb-ft) @ Rated rpm: 436(322)@1,600 rpm
  • Full-flow spin-on filter
  • Turbocharged
  • Under-hood, dual element dry type, restriction indicator on filter housing for service
  • Direct Injection
  • Heavy duty inboard-mounted planetary
  • Type: Powershift | Torque Converter: Single-stage, Dual-phase, Quad-element torque | Operator Interface: Steering column lever for two gears forward and one in reverse | Shift Modes: Manual activation (Forward: 1st and 2nd; Reverse: 1st)
  • Helical bevel gear
  • Type: Articulated frame, fully hydraulic | Articulation Angle: 35 degrees | Raise sec.: 5.1 | Dump sec.: 1.1 | Lower sec. : 3.0 | Total sec.: 9.2
  • 2-12 volt: 120A
  • 24 Volts
  • 70 Amp
  • Rear Axel Oscillation (with 17 R 25 tires): 25 degrees (12.5 degrees each direction)
  • Service: Pneumatically assisted, hydraulically actuaded, four wheels disk brake
  • Manually activated, drum mounted on front output shaft
  • 17 R 25 12 Ply: (Tread Width 1,900 mm (74.8 in) | Width Over Tires: 2,350 mm (92.5 in) )
  • 16 R 24 10 Ply: (Tread Width 1,600 mm (63.0 in) | Width Over Tires: 2,010 mm (79.1 in) )
  • 0.3 Mpa (43 psi)
  • 0.3 Mpa (43 psi)
  • Maximum Travel Speeds (with 16 R 24 tires) 1st Gear: 7 km/h (5 mph) | Maximum Travel Speeds (with 16 R 24 tires) 1st Gear: 8 km/h (5 mph) | Maximum Travel Speeds (with 16 R 24 tires) 2nd Gear: 16 km/h (10 mph)
  • Hydraulic: Z-Bar
  • Breakout Force: 9,600 Kg (21,164 lb) | Max. Rollback at Ground Level: 49 degrees | Max. Rollback, Boom Fully Raised: 57 degrees | Max. Bucket Dump Angle, Fully Raised: 45 degrees
  • System Relief Pressure (Loader and Steering): 16 Mpa (2,321 psi)
  • Pump (Loader and Steering): Gear Pump, variable displacement, closed-center
  • Max. Rated Flow at 2,200 rpm L/min (gpm): 100(26)
  • Reach, 45 degree Dump, 2,130mm (7ft) Clearance: 1,470 mm (4.8 ft) | Loader Clearance Circle, Bucket Carry Position: 11,200 mm (36.7 ft)
  • Steering (measured to centerline of outside tire): 4,950 mm (16.2 ft)
  • Top of Cab and Canopy: 3,120 mm (10.2 ft) | Hood: 3,010 mm (9.9 ft) | Hinge Pin, Fully Raised: 3,732 mm (12.2 ft) | Dump Clearance, 45 degree Full Height: 2,850 mm (9.4 ft) | Reach, 45 degree Dump, Full Height: 1,030 mm (3.4 ft)
  • 370 mm (1.2 ft)
  • 2,750 mm (9.0 ft)
  • Bucket on Ground: 6,863 mm (22.5 ft)
  • Max. Digging Depth: 90 mm (0.3 ft)
  • Bucket: 2,460 mm (8.1 ft)
  • Tank: 130 L (34 gal)
  • 15 L (4 gal)
  • Engine: 13.5 L (4 gal)
  • 35 L (9 gal)
  • Axle Oil (Front and Rear, each): 11 L (3 gal)
  • Tank: 120 L (32 gal)
  • Fan Drive: Belt driven | Loader Controls: Dual-multiway valve, joystick control
  • 1.8 m3 (2.4 cu. Yd)
  • 1.4 m3 (1.8 cu. Yd)
  • Tipping Load, Straight: 9,020 Kg (19,886 lb) | Tipping Load, 35 degree Full Turn: 8,135 Kg (17,935 lb)
  • Bucket: 1,020 Kg (2,249 lb)
  • Operating: 10,200 Kg (22,487 lb)