2020 Rhino Equipment Wheel Loaders RWL186

Information

2020 Rhino Equipment Wheel Loaders RWL186

Rhino® Wheel Loaders are today’s solution to meet high performance requirments, have maximum uptime, and low cost operation. Designed to keep you competitive, these loaders let you finish the job faster and put more profit in your pocket.

The RWL series allows you to work hard and efficiently in all conditions. Repeatable fine modulation gives superior bucket control with less spillage. RWL Series electro-hydraulic implement controls and load-sensing hydraulic system with simultaneous lift and tilt capabilities offer better control with less effort.

Rhino® wheel loaders saves you money by keeping operating costs to a minimum – getting more work done per unit of fuel used.

Features may include:

  • If you`ve got maximum productivity in mind, the RWL Series Loaders should be at the top of your list. But it`s not just their big torque reserves thet make them such impressive performers. Joystick control provide smooth, near-effortless control. Rhino® hydraulics sense the load and deliver the flow needed for smooth combined functions and fast work cycles.
  • Control panel provides access to critical machine info, brake and throttle pedals are conveniently positioned for maximum comfort to the operator.
  • Rhino® cylinders offer superior strength and dent resistance deliver longer component life and reduced risk of system contamination. Rhino® Cylinders and Rods are designed to allow for a variety of service / repair options.
  • High quality hose products mean fewer hose changes. Rhino® Equipment offers a broad line of high, medium and low-pressure hoses and couplings that are engineered and tested far beyond industry standards for top performance and long life.

Photos

Highlights

  • Albany, Georgia
  • 2020
  • Rhino Equipment
  • Wheel Loaders RWL186
  • Model: 6CTAA8
  • Type: Powershift | Torque Converter: Single-stage, Dual-phase, Quad-element torque | Operator Interface: Steering column lever for two gears forward and one in reverse | Shift Modes: Manual activation (Forward: 1st and 2nd; Reverse: 1st)
  • Available
  • Bucket: 3,064 mm (10.1 ft)
  • Top of Cab and Canopy: 3,565 mm (11.7 ft) | Hood: 3,445 mm (11.3 ft) | Hinge Pin, Fully Raised: 4,300 mm (14.1 ft) | Dump Clearance, 45 degree Full Height: 3,028 mm (9.9 ft) | Reach, 45 degree Dump, Full Height: 1,320 mm (4.3 ft)

Specifications

  • 2020
  • Rhino Equipment
  • Wheel Loaders
  • RWL186
  • Large
  • Model: 6CTAA8
  • Cummins | Rhino®
  • Tier2
  • 6
  • 8.3 L (506 cu. In)
  • Net Power kW (Hp) @ Rated rpm: 179(240)@ 2,200 rpm
  • Net Peak Torque Nm (lb-ft) @ Rated rpm: 1,146(845)@ 1,500 rpm
  • Full-flow spin-on filter
  • Turbocharged, charge air cooled
  • Under-hood, dual element dry type, restriction indicator on filter housing for service
  • Direct Injection
  • Heavy duty inboard-mounted planetary
  • Type: Powershift | Torque Converter: Single-stage, Dual-phase, Quad-element torque | Operator Interface: Steering column lever for two gears forward and one in reverse | Shift Modes: Manual activation (Forward: 1st and 2nd; Reverse: 1st)
  • Helical bevel gear
  • Type: Articulated frame, fully hydraulic | Articulation Angle: 35 degrees | Raise sec.: 6.0 | Dump sec.: 1.9 | Lower sec. : 3.9 | Total sec.: 11.8
  • 2-12 volt: 120A
  • 24 Volts
  • 70 Amp
  • Rear Axel Oscillation (with 23.5 R 25 tires): 20 degrees (10 degrees each direction)
  • Service: Pneumatically assisted, hydraulically actuaded, four wheels disk brake
  • Manually activated, drum mounted on front output shaft
  • 23.5 R 25 16 Ply: (Tread Width 2,300 mm (90.6 in) | Width Over Tires: 2,897 mm (114.1 in) )
  • 23.5 R 25 16 Ply: (Tread Width 2,300 mm (90.6 in) | Width Over Tires: 2,897 mm (114.1 in) )
  • Maximum Travel Speeds (with 23.5 R 25 tires) 1st Gear: 12 km/h (7 mph) | Maximum Travel Speeds (with 23.5 R 25 tires) 1st Gear: 14 km/h (9 mph) | Maximum Travel Speeds (with 23.5 R 25 tires) 2nd Gear: 38 km/h (23 mph)
  • Hydraulic: Z-Bar
  • Breakout Force: 18,600 Kg (41,006 lb) | Max. Rollback at Ground Level: 50 degrees | Max. Rollback, Boom Fully Raised: 67 degrees | Max. Bucket Dump Angle, Fully Raised: 48 degrees
  • Pump (Loader and Steering): Gear Pump, variable displacement, closed-center
  • Max. Rated Flow at 2,200 rpm L/min (gpm): 180 (48)
  • System Relief Pressure (Loader and Steering): 20 Mpa (2,901 psi)
  • Reach, 45 degree Dump, 2,130 mm (7ft) Clearance: 2,100 mm (6.9 ft) | Loader Clearance Circle, Bucket Carry Position: 15,965 mm (52.4 ft)
  • Steering (measured to centerline of outside tire): 6,400 mm (21.0 ft)
  • Top of Cab and Canopy: 3,565 mm (11.7 ft) | Hood: 3,445 mm (11.3 ft) | Hinge Pin, Fully Raised: 4,300 mm (14.1 ft) | Dump Clearance, 45 degree Full Height: 3,028 mm (9.9 ft) | Reach, 45 degree Dump, Full Height: 1,320 mm (4.3 ft)
  • 460 mm (1.5 ft)
  • 3,300 mm (10.8 ft)
  • Bucket on Ground: 8,280 mm (27.2 ft)
  • Max. Digging Depth: 212 mm (0.7 ft)
  • Bucket: 3,064 mm (10.1 ft)
  • Tank: 350 L (92 gal)
  • 22 L (6 gal)
  • Engine: 19 L (5 gal)
  • 45 L (12 gal)
  • Axle Oil (Front and Rear, each): 20 L (5 gal)
  • Tank: 250 L (66 gal)
  • Fan Drive: Belt driven | Loader Controls: Dual-multiway valve, joystick control
  • 3.5 m3 (4.6 cu. Yd)
  • 3.0 m3 (3.9 cu. Yd)
  • Tipping Load, Straight: 14,057 Kg (30,990 lb) | Tipping Load, 35 degree Full Turn: 12,850 Kg (28,329 lb)
  • Bucket: 1,650 Kg (3,638 lb)
  • Operating: 18,600 Kg (41,006 lb)