2020 Rhino Equipment Wheel Loaders RWL315

Information

2020 Rhino Equipment Wheel Loaders RWL315

Rhino® Wheel Loaders are today’s solution to meet high performance requirments, have maximum uptime, and low cost operation. Designed to keep you competitive, these loaders let you finish the job faster and put more profit in your pocket.

The RWL series allows you to work hard and efficiently in all conditions. Repeatable fine modulation gives superior bucket control with less spillage. RWL Series electro-hydraulic implement controls and load-sensing hydraulic system with simultaneous lift and tilt capabilities offer better control with less effort.

Rhino® wheel loaders saves you money by keeping operating costs to a minimum – getting more work done per unit of fuel used.

Features may include:

  • If you`ve got maximum productivity in mind, the RWL Series Loaders should be at the top of your list. But it`s not just their big torque reserves thet make them such impressive performers. Joystick control provide smooth, near-effortless control. Rhino® hydraulics sense the load and deliver the flow needed for smooth combined functions and fast work cycles.
  • Control panel provides access to critical machine info, brake and throttle pedals are conveniently positioned for maximum comfort to the operator.
  • Rhino® cylinders offer superior strength and dent resistance deliver longer component life and reduced risk of system contamination. Rhino® Cylinders and Rods are designed to allow for a variety of service / repair options.
  • High quality hose products mean fewer hose changes. Rhino® Equipment offers a broad line of high, medium and low-pressure hoses and couplings that are engineered and tested far beyond industry standards for top performance and long life.

Photos

Highlights

  • Albany, Georgia
  • 2020
  • Rhino Equipment
  • Wheel Loaders RWL315
  • Cummins Model: M11
  • Type: Powershift | Torque Converter: Single-stage, Dual-phase, Quad-element torque | Operator Interface: Steering column lever for two gears forward and one in reverse | Shift Modes: Manual activation (Forward: 1st and 2nd; Reverse: 1st)
  • Available
  • Bucket: 3,500 mm (11.5 ft)
  • Top of Cab and Canopy: 3,832 mm (12.6 ft) | Hood: 3,720 mm (12.2 ft) | Hinge Pin, Fully Raised: 4,460 mm (14.6 ft) | Dump Clearance, 45 degree Full Height: 3,325 mm (10.9 ft) | Reach, 45 degree Dump, Full Height: 1,400 mm (4.6 ft)

Specifications

  • 2020
  • Rhino Equipment
  • Wheel Loaders
  • RWL315
  • Large
  • Cummins Model: M11
  • Cummins | Rhino®
  • Rating: Tier2
  • 6
  • 11 L (671 cu. In)
  • Net Power kW (Hp) @ Rated rpm: 250(335)@ 2,100 rpm
  • Net Peak Torque Nm (lb-ft) @ Rated rpm: 1,674(1,235)@ 1,500 rpm | Torque Rise: 47%
  • Full-flow spin-on filter
  • Turbocharged, charge air cooled
  • Under-hood, dual element dry type, restriction indicator on filter housing for service
  • Direct Injection
  • Heavy duty inboard-mounted planetary
  • Type: Powershift | Torque Converter: Single-stage, Dual-phase, Quad-element torque | Operator Interface: Steering column lever for two gears forward and one in reverse | Shift Modes: Manual activation (Forward: 1st and 2nd; Reverse: 1st)
  • Helical bevel gear
  • Type: Articulated frame, fully hydraulic | Articulation Angle: 40 degrees | Raise sec.: 6.0 | Dump sec.: 3.4 | Lower sec. : 1.6 | Total sec.: 11.0
  • 2-12 volt: 120A
  • 24 Volts
  • 70 Amp
  • Rear Axel Oscillation (29.5-25 -22PR L-3): 24 degrees (12 degrees each direction)
  • Service: Pneumatically assisted, hydraulically actuaded, four wheels disk brake
  • Electronically activated
  • 29.5-25 -22PR: (Tread Width 2,450 mm (96.5 in) | Width Over Tires: 3,200 mm (126.0 in) )
  • 29.5-25 -22PR: (Tread Width 2,450 mm (96.5 in) | Width Over Tires: 3,200 mm (126.0 in) )
  • Maximum Travel Speeds (with 29.5 R 25 tires) 1st Gear Forward: 6.4 km/h (4.0 mph) | Maximum Travel Speeds (with 29.5 R 25 tires) 1st Gear Reverse: 12 km/h (8 mph) | Maximum Travel Speeds (with 29.5 R 25 tires) 2nd Gear Forward: 11.9 km/h (7.4 mph) | Maximum Travel Speeds (with 29.5 R 25 tires) 2nd Gear Reverse: 11.9 km/h (7.4 mph) | Maximum Travel Speeds (with 29.5 R 25 tires) 3nd Gear Forward: 18.7 km/h (11.6 mph) | Maximum Travel Speeds (with 29.5 R 25 tires) 3nd Gear Reverse: 25.9 km/h (16.1 mph) | Maximum Travel Speeds (with 29.5 R 25 tires) 4nd Gear Forward: 37.0 km/h (23.0 mph)
  • Hydraulic: Z-Bar
  • Breakout Force: 26,400 Kg (58,202 lb) | Max. Drawbar Force: 26,900 Kg (59,304 lb) | Max. Rollback at Ground Level: 50 degrees | Max. Rollback, Boom Fully Raised: 67 degrees | Max. Bucket Dump Angle, Fully Raised: 48 degrees
  • Pump (Loader and Steering): Gear Pump, variable displacement, closed-center
  • Max. Rated Flow at 1,920 rpm L/min (gpm): 210 (55)
  • System Relief Pressure (Loader): 26 Mpa (3,771 psi) | System Relief Pressure (Steering): 21 Mpa (3,046 psi)
  • Reach, 45 degree Dump, 2,130 mm (7ft) Clearance: 2,020 mm (6.6 ft) | Loader Clearance Circle, Bucket Carry Position: 15,022 mm (49.3 ft)
  • Steering (measured to centerline of outside tire): 6,614 mm (21.7 ft)
  • Top of Cab and Canopy: 3,832 mm (12.6 ft) | Hood: 3,720 mm (12.2 ft) | Hinge Pin, Fully Raised: 4,460 mm (14.6 ft) | Dump Clearance, 45 degree Full Height: 3,325 mm (10.9 ft) | Reach, 45 degree Dump, Full Height: 1,400 mm (4.6 ft)
  • 461 mm (1.5 ft)
  • 3,650 mm (12.0 ft)
  • Bucket on Ground: 9,343 mm (30.7 ft)
  • Max. Digging Depth: 250 mm (0.8 ft)
  • Bucket: 3,500 mm (11.5 ft)
  • Tank: 480 L (127 gal)
  • 55 L (15 gal)
  • Engine: 32 L (8.5 gal)
  • 43 L (11 gal)
  • Axle Oil (Front and Rear, each): 51 L (13 gal)
  • Tank: 260 L (69 gal)
  • Fan Drive: Belt driven | Loader Controls: Dual-multiway valve, joystick control
  • 5.1 m3 (6.7 cu. Yd)
  • 4.4 m3 (5.8 cu. Yd)
  • Tipping Load, Straight: 18,000 Kg (39,683 lb) | Tipping Load, 35 degree Full Turn: 16,500 Kg (36,376 lb)
  • Bucket: 3,100 Kg (6,834 lb)
  • Operating: 31,500 Kg (69,446 lb)